Avocent MERGEPOINT 53XX SP MANAGER User's Guide Page 104
- Page / 236
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
To add a route or set the appliance as a default gateway at the user’s workstation:
NOTE: This procedure is provided for your convenience, but specific steps may vary depending on the host
operating system. For more information, see the installer/user guide for the host operating system.
Open the Internet Protocol (TCP/IP) Properties window and enter the MergePoint SP manager IP
address in the default gateway field.
-or-
Add a route by entering the appropriate command for your operating system; for example:
C:\Documents and Settings\admin>route add 192.168.1.20 mask
255.255.255.255 172.26.26.23
To directly connect to a native interface on a service processor:
NOTE: Before accessing the native interface, make sure you have already added a route or set the appliance as
the default gateway for the host.
1. In the side navigation bar, click an SP name.
2. Click the Configuration tab.
3. In the top navigation bar, click Native IP, then click Go to native IP interface.
NOTE: The Go to native IP interface option is not visible if Native IP is not enabled.
Native IP operations using SSH Commands
Admin users can create Native IP trusts and open Native IP connections with SSH commands.
Admin users can specify what IP addresses from which interfaces are trusted to bring up direct
connection to service processors.
To login to the MergePoint SP manager console as admin user:
You may log in to the MergePoint SP manager with any of the SSH clients, such as PuTTY
tool, SecureCRT tool or OpenSSH client. The following command examples use the OpenSSH
client under a Linux terminal.
Run the command by entering the following:
admin@MergePoint:~$ ssh -t username@MergePoint_IP_or_DNS_name
For example:
admin@MergePoint:~$ ssh -t admin@172.26.25.173
To enable selective mode:
Run the command by entering the following:
admin@MergePoint:~$ nativeipctl truston 0.0.0.0/0.0.0.0
92 MergePoint® SP Manager Installer/User Guide
- MERGEPOINT® SP MANAGER 1
- European Union Notification 2
- USA Notification 2
- Canadian Notification 2
- Japanese Notification 2
- Korean Notification 2
- MergePoint® SP Manager 3
- Product Overview 13
- Supported SPs 14
- Chapter 1: Product Overview 3 15
- SP5x00 manager is turned on 16
- Chapter 1: Product Overview 5 17
- Safety Precautions 18
- -tilt bar 19
- Installation and Setup 23
- Connecting to the Network 25
- Parameters on page 136 27
- Installation 28
- MergePoint SP manager 33
- Firewall/Packet Filtering 37
- Service Processor Licenses 45
- Automatically Manage SPs 46
- Manually Adding a Single SP 48
- Managing user accounts on SPs 57
- (Admin Users Only) 58
- Operations 61
- Monitoring and Management 67
- Viewing IML events 68
- Viewing the accounting log 68
- Import/export data 69
- Accessing FRU information 69
- Using the Alerts Viewer 70
- Schedules 74
- SNMP Access 75
- .1.3 instead of 1.3 76
- SP Operations 80
- Viewing SP information 81
- Changing the SoL port number 81
- Changing SP parameters 82
- Accessing system information 83
- Recovering provisioning 83
- Changing LAN parameters 84
- Host table 84
- Static routes 85
- Configuring SoL parameters 86
- Remote Control 87
- Diagnostics 87
- Appliance Operations 88
- SP Sessions and Connections 91
- Active sessions 92
- SoL Sessions 93
- SP Console Sessions 94
- Telnet Sessions 94
- SSH Sessions 95
- DirectCommand Sessions 98
- Native IP Connections 101
- 255.255.255.255 172.26.26.23 104
- 172.26.25.157 106
- <device IP address> 106
- Configuring External 107
- Authentication Services 107
- Administration Tasks Not 115
- The SSH command line format 116
- User shell 117
- SSH Passthrough 118
- Command Name Description 120
- Access_Servers = /bin/spshell 121
- Configuring Routes With CLI 122
- Using the CLI Utility 133
- CLI Options 134
- CLI Parameters and Arguments 135
- Autocompletion 137
- CLI Commands 138
- Synopsis 143
- Examples 143
- Using SMASH Command Line 161
- Protocol 161
- SMASH CLP Overview 162
- Supported profiles 163
- General command syntax 165
- Starting a SMASHCLP session 167
- Using Commands 168
- Associations 169
- Server commands 175
- Using WS-Management 183
- Properties 184
- Power Management 188
- WinRM Examples 195
- Enter the following command: 196
- Openwsman CLI Examples 198
- Appendix A: Technical Support 205
- Appendices 195 207
- Appendix C: Troubleshooting 209
- Appendix D: Access Privileges 212
- SP users 213
- • To set VNC for an SP 215
- Appendices 203 215
- Creating custom families 218
- [command1 220
- Exit Code Definition 221
- 0 Success 221
- Creating a profile 222
- Configuring command templates 222
- Appendices 213 225
- Appendices 217 229
- Telnet session 232
- License Information 233
- License Information 223 235
- For Technical Support: 236
Related products and manuals for Software Avocent MERGEPOINT 53XX SP MANAGER
Software Avocent AVWorks User's Guide
(80 pages)
(80 pages)
Software Avocent DSView 3 User's Guide
(108 pages)
(108 pages)
Software Avocent DSView User Manual
(8 pages)
(8 pages)
Software Avocent DSView 3 User's Guide
(13 pages)
(13 pages)
Software Avocent DSView 3 User Manual
(4 pages)
(4 pages)
© 2020, manymanuals.com. All rights reserved. | 1.326 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals