Avocent CCM1640 User Manual Page 16
- Page / 100
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
10 CCM840/1640 Installer/User Guide
Installing the CCM
WARNING: The power outlet should be installed near the equipment and should be
easily accessible.
To install the CCM hardware:
1. Locate the CCM where you can connect cables between the serial devices
and the CCM serial ports, and where you can connect a LAN interface
cable between the Ethernet hub or switch and the CCM LAN connector.
If you are using a rack mount kit, follow the instructions included with
the kit.
2. Connect serial devices to the CCM serial ports; see Appendix B for
cabling information. Connect each serial device to its appropriate power
source, following the device’s documentation.
3. Attach a 10BaseT or 100BaseT LAN interface cable to the LAN connector on
the back of the CCM. A CAT 5 cable is required for 100BaseT operation.
4. Insert the power cord into the back of the CCM. Insert the other end of the
power cord into a grounded electrical receptacle.
5. Check that the POWER LED on the front of the CCM is illuminated. If not,
check the power cable to ensure that it is inserted snugly into the back of
the unit. The ONLINE LED will illuminate within one minute to indicate
that the unit self-test is complete. If the ONLINE LED blinks, contact
Equinox Technical Support for assistance.
6. Check that the LINK LED is illuminated. If not, check the Ethernet cable
to ensure that both ends are correctly inserted into their jacks. If the unit is
connected to a 100 MB Ethernet hub, the 100MBps LED will be illuminated.
7. Once the POWER, ONLINE and LINK LEDs are illuminated, remove
power from the CCM and proceed with the confi guration process.
WARNING: The CCM840/1640 and all attached devices should be powered down before
servicing the unit. Always disconnect the power cord from the wall outlet.
Configuring the CCM
To configure the CCM840/1640, you must enter a unique IP address and
the network’s subnet mask. This information will be stored in the unit’s
configuration database. During initial login, you will specify a password for the
Admin user.
- CCM840/1640 1
- USA Notification 4
- Canadian Notification 4
- Japanese Notification 4
- Agency Approvals 4
- Table of Contents 5
- Product Overview 7
- Chapter 1: Product Overview 9
- Safety Precautions 10
- Using AVWorks 11
- Installation and 13
- Configuration 13
- Hardware Overview 15
- Configuring the CCM 16
- Installing the CCM 16
- Initial CCM login 19
- Reinitializing the CCM 20
- Operations 21
- Chapter 3: Operations 23
- Connecting to Serial Devices 24
- Chapter 3: Operations 21 27
- Chapter 3: Operations 23 29
- SSH Authentication Methods 30
- Chapter 3: Operations 25 31
- To display SSH information: 32
- Telnet CLI mode 33
- Ending device sessions 33
- Managing User Accounts 34
- To delete a user: 35
- Access rights and levels 36
- Using Authentication Modes 37
- Authentication summary 38
- Using Security Lock-out 39
- To unlock a locked-out user: 40
- Port History Mode Commands 41
- To access port history mode: 42
- Managing the CCM Using SNMP 43
- Chapter 3: Operations 39 45
- Using CCM Commands 47
- Accessing the CLI 49
- Entering Commands 49
- Understanding Conventions 50
- Command Summary 52
- CCM Commands 57
- Chapter 5: CCM Commands 59
- Port Commands 60
- Port Alert Copy command 61
- Port Alert Delete command 61
- Port Break command 62
- Port History command 62
- Port Logout command 63
- Port Set command 64
- Quit Command 66
- Resume Command 66
- Server Commands 66
- Server CLI command 67
- Server FLASH command 68
- Server PPP command 69
- Server RADIUS command 70
- Server Reboot command 71
- Server Security command 72
- Server Set command 73
- Server SNMP command 73
- Server SNMP Community command 73
- Server SNMP Manager command 74
- Server SNMP Trap command 75
- Server SSH command 76
- Show Commands 77
- Show Port Command Parameter 78
- Show Port Alert command 79
- Show Server command 79
- Show Server CLI command 80
- Show Server PPP command 80
- Show Server RADIUS command 81
- Show Server Security command 81
- Show Server SNMP command 81
- Show User command 82
- SPC Command 83
- User Commands 83
- User Delete command 85
- User Logout command 85
- User Set command 86
- User Unlock command 87
- Appendices 89
- Appendix B: Device Cabling 92
- Appendices 87 93
- Reversing Cables and Adaptors 94
- Appendices 89 95
- Appendix C: Ports Used 96
- Appendix D: Technical Support 97
- 590-364-001B 100
- For Technical Support: 100
Related products and manuals for Hardware Avocent CCM1640
Hardware Avocent CCM User Manual
(136 pages)
(136 pages)
Hardware Avocent CCS4016-001 User Manual
(2 pages)
(2 pages)
Hardware Avocent DSR8035 User Manual
(230 pages)
(230 pages)
Hardware Avocent CCM4850 User Manual
(100 pages)
(100 pages)
Hardware Avocent EVR1500-AM User Manual
(79 pages)
(79 pages)
Hardware Avocent 5240 User Manual
(88 pages)
(88 pages)
Hardware Avocent ACS V6000 User Manual
(58 pages)
(58 pages)
© 2020, manymanuals.com. All rights reserved. | 4.224 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals